Preparing for a Subcutaneous Injection

The location of injection is important for subcutaneous injections. The drug needs to be injected into the fatty tissue just below the skin. Some areas of the body have a more easily accessible layer of tissue, where a needle injected under the skin will not hit muscle, bone, or blood vessels.

The most common injection sites are:

  • Abdomen: at or under the level of the belly button, about two inches away from the navel
  • Arm: back or side of the upper arm
  • Thigh: front of the thigh

Equipment used for subcutaneous injections includes:

  • Medication: Vials of liquid medication can be single-use or multiuse. Vials can also be filled with a powder to which liquid needs to be added.
  • Syringes: The needles are short, at 5/8 inches long. The thickness of the needle is usually 25 or 27 gauge. There may be other options for doses more than 1 mL or for children or people with visual impairments.
  • Auto-injector pen: Some medications are available in a “pen” with a short single-use needle screwed onto the end of a pen-shaped, multiuse vial. The amount of medication needed is then dialed in at the end. As mentioned earlier, emergency medications like epinephrine can also come in this form.

How to Administer a Subcutaneous Injection

  1. Wash your hands. Wash your hands with soap and warm water to prevent potential infection. Be sure to thoroughly scrub between fingers, on the backs of hands, and under fingernails. The Centers for Disease Control and Prevention (CDC)Trusted Source recommends lathering for 20 seconds — the time it takes to sing “Happy Birthday” twice.
  2. Gather supplies. Assemble the following supplies:
    • needle and syringe with medication or auto-injector pen
    • alcohol pads
    • gauze
    • puncture-resistant container to discard the used needles and syringe (typically a red, plastic “sharp’s container”)
    • bandages
  1. Clean and inspect the injection site. Before injecting medication, inspect your skin to make sure there’s no bruising, burns, swelling, hardness, or irritation in the area. Alternate injection sites to prevent damage to an area with repeated injections. Then you should clean the skin with an alcohol swab. Let the alcohol dry thoroughly before doing the injection.
  2. Prepare the syringe with medication. Before withdrawing medication from a vial and injecting yourself or someone else, make sure you’re using the correct medication, at the correct dose, at the correct time, and in the right manner. Use a new needle and syringe with every injection.
  3. Pinch your skin. Take a big pinch of skin between your thumb and index finger and hold it. (Your thumb and forefinger should be about an inch and a half apart.) This pulls the fatty tissue away from the muscle and makes the injection easier.
  4. Inject the needle. Inject the needle into the pinched skin at a 90-degree angle. You should do this quickly, but without great force. If you have very little fat on your body, you may need to inject the needle at a 45-degree angle to the skin.
  5. Insert the medication. Slowly push the plunger to inject the medication. You should inject the entire amount of medication.
  6. Withdraw the needle. Let go of the pinched skin and withdraw the needle. Discard the used needle in a puncture-resistant sharp’s container.
  7. Apply pressure to the site. Use gauze to apply light pressure to the injection site. If there’s any bleeding, it should be very minor. You may notice a little bruising later. This is common and nothing to be concerned about.

Preparing a syringe

Remove the cap from the vial. If the vial is multidose, make a note about when the vial was first opened. The rubber stopper should be cleaned with an alcohol swab.

Draw air into the syringe. Draw back the plunger to fill the syringe with air up to the dose that you’ll be injecting. This is done because the vial is a vacuum, and you need to add an equal amount of air to regulate the pressure. This makes it easier to draw the medication into the syringe. Don’t worry, though — if you forget this step, you can still get the medication out of the vial.

Insert air into the vial. Remove the cap from the needle and push the needle through the rubber stopper at the top of the vial. Inject all the air into the vial. Be careful to not touch the needle to keep it clean.

Withdraw the medication. Turn the vial and syringe upside down so the needle points upward. Then pull back on the plunger to withdraw the correct amount of medication.

Remove any air bubbles. Tap the syringe to push any bubbles to the top and gently depress the plunger to push the air bubbles out.

Preparing an auto-injector

  • If you’re using a pen delivery system, attach the needle to the pen.
  • The first time you use the pen, you’ll need to prime it to push out extra air in the delivery system.
  • Dial a small dose (usually 2 units or 0.02 mL, or as indicated by the package instructions) and push the button to expel the primer.
  • Dial the correct dose and prepare for your injection.
  • Inject the medication.

Complications of Subcutaneous Injection

If you’ll be doing this type of injection for more than one dose or for multiple days, you’ll need to rotate the injection sites. This means that you shouldn’t inject medicine into the same spot twice in a row.

For example, if you injected medicine into your left thigh this morning, use your right thigh this afternoon. Using the same injection site over and over again can cause discomfort and even tissue damage.

As with any injection procedure, infection at the site of injection is a possibility. Signs of infection at the injection site include:

  • severe pain
  • redness
  • swelling
  • warmth or drainage

These symptoms should be reported to your physician immediately.